Camshaft - 20R/22R/RE .450" Lift Circle Track Cam
Camshaft - 20R/22R/RE .450" Lift Circle Track Cam
 
Alternate Views:


Our Price: $279.95
Shipping Delay: Subject to availability, please call for more info.

Part Number: 1022015


Acknowledgement*:
I acknowledge if I elect not to purchase rocker arms I am voiding my camshaft warranty.

Qty:  
Details Fitment Instructions
 

.450" Lift Circle Track

LC Engineering's .450" lift cam has been specifically designed for a circle track application where lift rules apply. We have taken a small lift cam profile and given it more duration and changed lobe centers to give you a camshaft that will not only pass thru tech but allow your 22R race engine to make more power higher in the rpm range where it is needed in a circle track application. LC Engineering recommends running dual valve springs for any application turning over 5,000 RPM consistently.

LC Engineering is constantly striving to improve both the quality and performance of our products. We test our camshafts on the street, race track and off-road. The results are an improved line of camshafts that offer a broader selection of grinds, increased horsepower, and higher quality. All LC Engineering Camshafts are ground on new billets and double heat-treated for long life. Each has been designed for maximum torque and horsepower, specifically for the application. When comparing camshaft profiles, always reference the duration @ .050" valve lift.

20R/22R Circle Track Camshaft - .450 Lift
Hot Street / Circle Track / Drag Race (2500-6500 rpm)
Circle Track where stock rules apply
Big duration for higher rpm ranges



Intake Exhaust
Valve Lash .008 .012
Valve Lift .450 .450
Advertised Duration 280° 280°
Duration @ .050" 262° 262°
Lobe Center 104° 104°

  • Intake Opens 27º BTDC
  • Intake Closes 55º ABDC
  • Exhaust Opens 55º BBDC
  • Exhaust Closes 27º ATDC

NOTE: Will not work with the stock 22RE or 22RTE computer. It requires an aftermarket stand alone engine management system like one of these we offer:

  • Haltech Elite 550 22RE Fuel Management System w/ Sub Harness Kit, see Part #: 1020220.
  • Haltech Elite 550 22RE Fuel Management System w/ Complete Harness Kit, see Part #: 1020221.
  • Pro Fuel Injection Kit #3 Naturally Aspirated 4 Cylinder, see Part #: 1063026.

NOTE: Always check the valve to piston clearance and valve to valve clearance with this camshaft! Piston notching may be required if you do not have .100" of valve to piston clearance at full lift. Failure to install this cam with matched valve train components can cause engine damage. LC Engineering highly recommends using our Pro Camshaft Kit to allow proper spring retainer to guide clearance for any cam that has over .450" lift or in any application that requires a sustained RPM of 6,000 or higher.

  • Pro Camshaft Kit, see Part #: 1020000.

NOTE: LC Engineering will not warranty any cam damage if you do not purchase new Toyota rocker arms from LC Engineering, or a complete rocker arm assembly from LC Engineering at the same time as purchasing our camshaft.

  • Individual rocker arms, see Part #: 1023015.
  • Complete rocker assembly, see Part #: 1023018.

Buyer beware on reground rockers in the market. Regrinding the pad on the rocker can remove the heat treated portion of the pad making for a soft rocker. Rocker arms that are reground will not have the factory geometry of a stock rocker. To regrind a rocker will take care of the face surface but will do nothing to address the rocker shaft bore, a loose rocker bore will make adjustment difficult and will never be correct which is why we cannot warranty a camshaft unless new rockers are purchased with a camshaft.


This product should not be used in a manner that violates Federal EPA Laws.


Contact our Tech Support Line for further information at 928-855-6341.

Check out LCEngineering.com for New Products, Tech Articles, Specials & Monthly Newsletters!

Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501.


Suggested with your install...
OE Rocker Set With Adjusters & Nuts 20R/22R/RE/RTE Tools - Plastigage (.001" to .003") OEM Rocker Set With Adjusters & Nuts 20R/22R/RE/RTE Cam Degree Kit - 20R/22R/RE/RET
Our Price: $189.99

Add
Our Price: $5.49

Add
Our Price: $399.95

Add
Our Price: $149.95

Add
O.E. Rocker Arm Set  With Adjusters & Nuts 20R/22R/RE Tools - Plastigage (.001" to .003") Rocker Arm Set  With Adjusters & Nuts 20R/22R/RE Cam Degree Kit - 20R/22R/RE/RET

Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 4 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 . May 5, 2021
Reviewer: Austin Lodin from Santa Rosa , CA United States  
Preforms great. Nothing bad to say. Everything came faster than expected as well.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Camshaft July 20, 2017
Reviewer: Anonymous Person  
Great customer service

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent March 7, 2017
Reviewer: Bob Patten from Clear Lake, IA United States  
Parts were shipped well and are of top quality.

Was this review helpful to you?

  1 of 2 people found the following review helpful:
 
5 of 5 Awesome June 27, 2016
Reviewer: Brad Shipley from Wenatchee, WA United States  
Cam has a nice lump at idle and strong power at higher rpms

Was this review helpful to you?