Stage 3 Torquer Camshaft 20R/22R/RE/RET
Stage 3 Torquer Camshaft 20R/22R/RE/RET
 

Our Price: $364.50

Quantity in Stock:2

Part Number: 1022030


Acknowledgement*:
I acknowledge if I elect not to purchase rocker arms I am voiding my camshaft warranty.

Qty:  
Details Fitment Instructions
 

Stage 3 Torquer Camshaft


This camshaft has one of the best torque curves you could ask for, which makes it perfect for rock crawling, rock racing or just about any large tire application. This cam produces gobs of torque as low as 1,500 RPM and keeps a nice broad, flat curve up to almost 5,000 RPM. This cam will require our Pro Camshaft Kit due to the large lift.

LC Engineering is continuously striving to improve both the quality and performance of our products. We test our camshafts on the street, race track and off-road. The results are an improved line of camshafts that offer a broader selection of grinds, increased horsepower, and higher quality. All LC Engineering Camshafts are ground on new billets and double heat-treated for a long life. Each has been designed for maximum torque and horsepower, specifically for the application. When comparing camshaft profiles, always reference the duration @ .050" valve lift.

20R/22R - Stage 3 Torquer Camshaft

4WD / Pre-Runner / Low End Torque (1500-5500 rpm)
Modified Carb or Throttle Body & 1 1/2" Header



Intake Exhaust
Valve Lash .008 .012
Valve Lift .500 .500
Advertised Duration 267° 267°
Duration @ .050" 234° 236°
Lobe Center 106° 109°
Lobe Separation 107.5°

Intake Opens 11º BTDC
Intake Closes 43º ABDC
Exhaust Opens 47º BBDC
Exhaust Closes 9º ATDC


NOTE: Will not work with the stock 22RE or 22RTE computer. It requires an aftermarket stand alone engine management system like one of these we offer:

  • Haltech Elite 550 22RE Fuel Management System w/ Sub Harness Kit, see Part #: 1020220.
  • Haltech Elite 550 22RE Fuel Management System w/ Complete Harness Kit, see Part #: 1020221.
  • Pro Fuel Injection Kit #3 Naturally Aspirated 4 Cylinder, see Part #: 1063026.

NOTE: Always check the valve to piston clearance and valve to valve clearance with this camshaft! Piston notching may be required if you do not have .100" of valve to piston clearance at full lift. Failure to install this cam with matched valve train components can cause engine damage. LC Engineering highly recommends using our Pro Camshaft Kit to allow proper spring retainer to guide clearance for any cam that has over .450" lift or in any application that requires a sustained RPM of 6,000 or higher.

  • Pro Camshaft Kit, see Part #: 1020000.

NOTE: LC Engineering will not warranty any cam damage if you do not purchase new Toyota rocker arms from LC Engineering, or a complete rocker arm assembly from LC Engineering at the same time as purchasing our camshaft.

  • Individual rocker arms, see Part #: 1023015.
  • Complete rocker assembly, see Part #: 1023018.

Buyer beware on reground rockers in the market. Regrinding the pad on the rocker can remove the heat treated portion of the pad making for a soft rocker. Rocker arms that are reground will not have the factory geometry of a stock rocker. To regrind a rocker will take care of the face surface but will do nothing to address the rocker shaft bore, a loose rocker bore will make adjustment difficult and will never be correct which is why we cannot warranty a camshaft unless new rockers are purchased with a camshaft.


This product should not be used in a manner that violates Federal EPA Laws.


Contact our Tech Support Line for further information at 928-855-6341.

Check out LCEngineering.com for New Products, Tech Articles, Specials & Monthly Newsletters!

Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501.


Suggested with your install...
OEM Rocker Set With Adjusters & Nuts 20R/22R/RE/RTE Cam Degree Kit - 20R/22R/RE/RET Tools - Plastigage (.001" to .003") OE Rocker Set With Adjusters & Nuts 20R/22R/RE/RTE
Our Price: $447.15

Add
Our Price: $155.95

Add
Our Price: $7.33

Add
Our Price: $189.99

Add
Rocker Arm Set  With Adjusters & Nuts 20R/22R/RE Cam Degree Kit - 20R/22R/RE/RET Tools - Plastigage (.001" to .003") O.E. Rocker Arm Set  With Adjusters & Nuts 20R/22R/RE

Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 2 Write a review.

  0 of 1 people found the following review helpful:
 
5 of 5 Cam July 16, 2021
Reviewer: Anonymous Person from Inarajan, Guam  
Great can nice sound!!!

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 Superior product! March 5, 2014
Reviewer: Jonathan Thorpe from Clarksville, TN United States  
I have window shopped on this site for a very long time and was thrilled when I could finally purchase a product. This cam may be the first purchase but not the last.. I love the Toyota 22R engines and you guys are the best of the best when it comes to the best 4 cylinder ever made.. I was suprised by the courtesy call you guys made after my purchase to make sure I had the proper parts, shows you guys really know what your doing..

Was this review helpful to you?