Home > ENGINE > TOP END > Cylinder Head > Cylinder Heads > 2RZ/3RZ CYLINDER HEADS >

2RZ/3RZ Cylinder Head Stage 3 2001-2004 4 Intake Ports
2RZ/3RZ Cylinder Head Stage 3 2001-2004 4 Intake Ports

Alternate Views:

Our Price: $2,999.95

NOTE:: Usually Ships in 1 to 2 Weeks
Part Number: 1021068

Cylinder Head Gasket Set*:

Would You Like To Add...

Head Bolts or Head Studs*:


2RZ/3RZ Cylinder Head Stage 3 2001-2004 4 Intake Ports

LC Engineering has the best upgrades for the dual over head cam 2RZ/3RZ engine. This Cylinder head will supply you with a High Performance head to upgrade 2RZ/3RZ performance engines. This is an excellent cylinder head choice to upgrade with our Stage 1 or 2 camshafts.

This cylinder head comes fully assembled with a high performance 3 angle valve job. Parts required for install that are NOT included, are Camshafts and OE buckets. There are NO Shims included. As you know the head must be torqued onto the engine block in order to perform valve shimming.

Cylinder Head Casting
We have seen all the import head castings the only one that is worth using is the OEM Toyota head casting. While this head casting cost more than 3 times the amount of the imported one this is the only one that has the quality to give you years of service.

Stainless Steel Intake & Exhaust Valves
These Stainless Steel valves are 1mm oversized, the exhaust valves is 31.5 mm, the intake valves are 38.5 mm, great for this ported head. These stainless steel valves are lighter than the stock steel valves, and have a special anti-friction coating to promote better airflow across the valve as well as reduced resistance in the guide, resulting in better valve train stability.

Pro Dual Valve Springs
The Pro Dual Valve Springs are a "must have" upgrade when running bigger lift cams and higher RPM's. With 75lbs of seat pressure and open pressure of 215lbs (at .500" lift) they will work perfectly with any naturally aspirated or low boost application (0-20 lbs of boost). These springs are rated up to 8,000 RPM and will accommodate cam lifts up to .600"!

Dual Spring Seat
As with all other areas in the valve train the area where the spring sits also takes a beating. The spring seats will sit under the Pro Dual valve spring and will hold up to the extreme pressures and higher RPM'S found in performance engines.

Titanium Retainers
Titanium valve spring retainers, will allow you gain speed and power, because LCE Titanium retainers are lighter and stronger than steel. Titanium is less than half the weight and ten times stronger than the factory steel retainer, these Titanium retainers allow you to use high lift cams without the chance of failure.

Hardened Keepers
A Set of Hardened Valve Keepers fit all 6mm valves using High Performance retainers.

Viton Valve Seals
Viton Valve Seals are the latest in valve seal material, surpassing Teflon! Heat resistant to 440 degrees, they eliminate oil consumption through the valve guide and provide smoother engine idling by stopping manifold air and oil leakage past the seal. They insure a perfect seal for maximum performance and long engine life.

Performance Porting
LCE has the experience necessary to port the cylinder heads for the utmost in efficiency. The Stage 3 porting will clean up casting inconsistencies while increasing the flow characteristics of both the exhaust and intake ports. The cylinder heads will also go though a complete deburring process.

Optional Parts not included

  • Stage 1 Camshaft Set Part Number 1022056
  • Stage 2 Camshaft Set Part Number 1022062
  • Fuel Injector Cup Set Part Number 1065013
  • Head Gasket Set Part Number 1024156
  • Head Bolts Part Number 1024072
  • Head Studs Part Number 1024075

Contact our Tech support line for further information: 928-855-6341.

Check out www.LCEngineering.com for New Products, Tech Articles,
Specials & Monthly Newsletters!

Newsletters! Or try our new web site LCEPerformance

Note: Images are for illustration purposes only. Images MAY NOT represent the product listed. Please contact Customer Service with any questions or concerns: 928-505-2501.

Share your knowledge of this product with other customers... Be the first to write a review