Street Header Kit 2WD Direct Fit 22R/RE 1985-1995 Pick Up
Some people don't know it but a header
makes the most power gain with a single bolt on part with no need of
complicated and super expensive modifications to your vehicle. It
increases an average of 10-15HP on your engine by increasing improved
flow in the exhaust system (Logic says: the faster everything comes out,
the faster everything can come in).
***Not for 4Runners***
50 State Legal C.A.R.B. EO: D-462-1
There are many headers in
the market these days, probably cheaper, but they are far from better.
LC Engineering has been producing, testing, installing and designing
these headers for more than 20 years. so we can assure you that there
is not a better header for a Toyota 22 engine series out there on the
market. So after installing your LC Engineering Street header on your
Toyota you will know why we still the #1 header around, why race and
off-road enthusiasts prefer us and why we are worth the extra expense.
Our most popular product are the street header kits. LCE uses all 304 1
1/2" Stainless steel tubing, 16 gauge .065 wall, the collector is made
in house with 409 Stainless steel. A huge 1/2" thick steel header to
head flange and 3/8" steel flanges at the collector that accepts the
stock Toyota round exhaust gasket. As if that were not enough, the whole
package is coated in a high temp ceramic coating. To make the install
easy on you LCE supplies you with all the gaskets needed to bolt your
header on your vehicle. Our header flanges are cut to allow the use of
OEM exhaust manifold gaskets. These gaskets feature a metal crush fire
ring and a heat deflector for the plug wires. No cheap paper gaskets to
blow out with a LC Engineering Header.
This header kit is for 85-95 2 Wheel drive trucks auto and manual transmissions, and includes an adjustable connector pipe that will connect to most factory catalytic converter.
***Not for 4Runners as they are built on a 4wd chassis, see item # 1041036***
This Complete Kit Includes:
- 2WD (82-95) Street Header
- 22R/RE Header Connector Pipe - 2WD
- Street Header Gasket Set (85-95 Specific)
Options For Header:
- O2 Sensor Extension (1065035) No Charge, Only Needed for 1984-1988
- O2 Block Plate Kit $5.00 (1045003)
- Header Air Injection Block Off Plates $15.00 (1045014)
- Header Stud Set $15.00 (1045030)
All Toyota Pickups and 4Runners manufactured before 1988 have a
factory non-heated single wire oxygen sensor. When installing our Street
Header Kit you will notice that the oxygen sensor provision has been
moved downstream from its factory location. We recommend that anyone
with a pre 1988 application utilize our universal 4 wire heated O2
sensor in replace of there factory single wire. This will not only
improve the signal but the gas mileage as well as the performance of the
vehicle. Vehicles made from 1988-1995 should have a factory heated O2
sensor and should not need to change it unless their factory one is
Universal Heated O2: 1065034 Sensor NOT CA Smog Legal
Over 27 years of producing these headers LC Engineering has made all attempts to make these header kits fit as best as possible. Unfortunately there are a very small amount of applications that may require more extensive modification or even fabrication to make the connector pipe fit correctly. This is mostly contributed to numerous changes in Toyota's production along with aftermarket modifications. LC Engineering offers full technical support to make your fitment as easy as possible but they will not be responsible for any "custom" connector pipes.
Contact our Tech Support Line for further information at 928-855-6341.
Check out www.LCEngineering.com for New Products, Tech Articles,
Specials & Monthly Newsletters!
Note: Images are for illustration purposes only. Images MAY NOT represent the product listed. Please contact Customer Service with any questions or concerns: 928-505-2501.