Pro Distributor
(w/ Vacuum Advance)
When was the last time you checked your ignition timing? If you are like most people it has been a while! An old worn out distributor can cause major tuning issues along with robbing your performance. Time to upgrade to an all new LC Engineering Pro Distributor. These distributors are brand new that have been changed with custom springs and weights to achieve maximum performance. We re-curve these distributors to advance much quicker than stock to provide excellent throttle response and quick acceleration. The vacuum advance unit is new for years of service.
The vacuum advance distributors are a "Must Have" for any mild performance or daily driver application. If you have a more radical application; off-road w/big tires, circle track drag race etc..., then you will want to check into our Pro Distributors without vacuum advance. The cap that is used has the better brass and copper terminals.
- For carbureted applications only
- This model will add 10° of Vacuum Advance and 18°- 20° Mechanical
- Fits 20R engines with magnetic pick-up only. 20R engines with points style ignition will require replacing stock igniter with a MSD-6AL Digital Ignition w/rev Control, see Part #:1082026 along with a MSD Blaster 2 Coil, see Part #:1082032.
| Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501. |
- 1975-1980 20R 2.2L Engines
- 1981-1995 22R 2.4L Engines
To open a printable PDF version of this instruction CLICK HERE
LC Pro Distributor: An absolute must for all performance applications, especially circle track, off-road, hot street or any race application. These Pro Distributors have a modified advance curve that will provide the appropriate ignition timing for your performance engine.
Vacuum advance applications: LC Engineering recommends setting the initial timing at 6°- 8° with the engine running below 1000 rpm and total timing of 28°- 32° w/o vacuum(34°- 36° w/vacuum connected) at 2500-3000 rpm. The LC Pro Distributor will add approx. 10° of vacuum advance and 18°- 20° of mechanical advance.
Non-vacuum advance applications: LC Engineering recommends setting the initial timing at 10°- 14° with the engine running below 1000 rpm and total timing of 28°- 32° at 2500-3000 rpm. The LC Pro Distributor will add approx. 18°- 20° of mechanical advance by 2000-2200 rpm.
LC Engineering recommends using a delay timing light to set total timing. Run engine at 2500-3000 RPM when setting total timing with a delay light. For LC Pro Distributors with Vacuum Advance, remove and plug vacuum hose before setting the initial or total timing. The pick-up air gap should be set between .007" and .010" on either distributor. This setting should be made with a non-ferrous (not magnetic) feeler gauge for accuracy. The LC Pro Distributors may be used with a factory igniter, LC Pro Crane Ignition Kits, or most other high output ignitions. Remove the negative battery cable before doing any modifications to your ignition system.
All above instructions are guidelines provided by LC Engineering based on years of research and development. Certain applications may vary from these guidelines slightly. LC Engineering strongly suggests that any modifications or maintenance done to the ignition system are done by a qualified technician. LCE also recommends that you check the timing and tuning of your vehicle, especially any hi performance application, often to avoid any possible engine malfunctions or failure.
Distributor Polarity: Positive wire is white. Negative wire is red. Be sure to confirm polarity when installing any aftermarket ignition kit (Crane, MSD etc"¦). Crossing wires will cause timing and tuning problems!
NOTE: LC Pro Distributors will use LC Engineerings Pro Cap and Rotor: Part #1081060 Cap and #1081057 Rotor.
35 Reviews Hide Reviews Show Reviews
-
Pro Distrbutor
Works great and a improvement over stock
-
distributor
added power off the bat
-
New Dizzy
The timing mark was jumpin all over the place, on my fresh, top end re-build, and the engine sounded like crap. I ordered a Pro Distributor on Thursday, it was here on Tuesday. It took all of 20min to swap out the tired, old, stock unit and have my ‘84 Toyo truck running like a champ. That’s what I call a win! Thanks LCE, for helping keep so many vintage rigs on the road and running great!! \\m//
-
Distributor Purchase...
Product works fabulously as always and customer service is above and beyond. If you're having problems with your Toyota these guys are the ones that can and will help you resolve the issue.
-
.
Great product! The distributor was purchased as a Christmas gift and the recipient is extremely impressed. The distributor has an amazing advance curve with superior response. Durability right out of the box, plug and play, Quality that surpasses OEM. Money well spent!
-
Pro Distributor w/ vacuum advance
Runs Great!! Had an autozone distributor that was impossible to tune on a fresh motor, bought this one and it runs like it should. No more hard starts or running issues throughout the power band. Thank you for your products, business!!
-
Pro Distributor With Vacuum Advance 20R/22R
What a difference from the stock distributor!Set the timing to 8 degrees advance, Installed Stage 2 Head, Stage 2 Mild Cam, 38 Weber Carburetor, 1 inch Spiral spacer, Offenhauser Dual Plane Intake, 1 1/2 Inch Header, Pro Spark Plug Wire Set!! A Great combination setup for this 22R on my 1987 Pickup 4X4 ! A lot of power!
-
Poor performance
The distributor I purchased from LCE is top notch. I spoke to one of your techs prior to purchasing and they were very knowledgeable and helpful. My project is now back on track thanks to the professionalism at LCE. I will be making future purchases based on your quality.
-
.
Love the way it performs I can feel the difference in the power.