LCE

OEM Flywheel Bolt (Set of 8) Connect that flywheel with confidence. These OEM flywheel bolts are just what the doctor ordered to connect your flywheel to your engine. They have a black oxide finish...

Thermostat Housing Gasket (Paper / Flat) Any time you replace the thermostat or remove the housing, you should replace the gasket to avoid future leaks. This gasket is a paper gasket that offers an...

Distributor Shaft O-Ring O-ring that seals the distributor shaft to the cylinder head. Keeps oil from leaking out and debris from getting in and contaminating the oil system. Contact our Tech...

Header Flange (You Choose Style) Steel header flange for custom fabrication of exhaust header on 20R, 22R, or 22RE engines. 1/2" thick flange with 1-1/2" or 1 5/8" ports. This header flange is the...

Rear Main Seal Housing Gasket This gasket seals the rear main seal housing to the block on 20R-22RE engines. Contact our Tech Support Line for further information at 928-575-2174...

Oxygen Sensor Gasket (2-Bolt Style) This gasket is a direct replacement for 2-bolt O2 sensors. If you have to replace the O2 sensor, you should replace the gasket as well to avoid pesky exhaust...

22RE Fuel Pressure Damper Washer This fuel damper washer is a stock replacement for the worn out one. You will need (1) as well as (1) of these 1025050 washers for each damper. NOTE: Sold...

Oil Feed Line (CT20 To Garrett GT25R) Looking for a replacement oil feed line for your GT25R turbo? Look no further, LC Engineering has everything you need. This particular line was designed for...

O-Ring (Water Block Plate on Cylinder Head) Replacement O-ring for our billet water plate. For our Billet race motors that use our water plate to eliminate the thermostat housing. Contact our...

Base Gasket Fix or prevent pesky vacuum leaks at the carburetor base by replacing the gasket between your stock 22R Aisin carb and the intake manifold. Genuine Toyota quality gasket. Contact...

Stage-3 The Stage 3 cam is designed to work with some larger valves, port work, and upgraded carburetor or EFI system. This cam starts moving the power band a little higher in the RPM range...

Stage-2 LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The 2RZ/3RZ Stage 2 Camshaft Set...

2RZ/3RZ - Stage 3 Camshaft Set LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The 2RZ/3RZ...

2RZ/3RZ Stage 3 Turbo Camshaft Set LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The...

Stage-4 LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The 2RZ/3RZ Stage 4 Camshaft Set...

Stage-5 LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The 2RZ/3RZ Stage 5 Camshaft Set is...

Stage 5 (Turbo) LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. With power potential over...

Stage 1 LC Engineering has the largest selection of Toyota cams anywhere which means that no matter what application you have we can get the right cam for you. The 2RZ/3RZ Pro Camshaft Set is the...

Crush Washer This Crush Washer is a stock replacement for the worn out ones on the Cold Start Injector on Toyota engines. Sold as each. You will need (2) for each cold start injector. NOTE: Sold...

Custom Brake Line (Upgrading to 1" Bore Master Cylinder) Because we know how much everybody hates making custom brake lines, this line comes ready to plug and play. It will bolt right onto your...