LCE Kit

Oil Pan Kit - 5VZ Taco (W/Solid Axle Swap)

SKU: 1013246
0
(No reviews yet) Write a Review
$439.14
Adding to cart… The item has been added

Oil Pan Kit 3.4L V6

(5VZ-FE Tacoma w/Solid Axle Swap)

When installing a solid axle swap kit on your 95-04 Tacoma, you will notice that your stock oil pan will interfere with the new solid axle. We have solved this problem with a T100 oil pan kit. This kit comes with a new oil pan, pick up tube w/gasket and the dipstick w/tube. This kit comes with all the parts you need to convert your 5VZ engine over to the T100 pan. You can get the maximum flex out of your solid axle suspension without worrying about hitting the oil pan.

Reference OEM Toyota Part #’s:

  • Oil Pick-Up Tube Gasket: 15147-62020
  • Oil Pick-Up Tube: 15104-62040
  • Oil Dipstick Tube: 11452-62060
  • Oil Pan: 12101-65030



Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501.

  • 5VZ Tacoma (w/Solid Axle Swap)

To open a printable PDF version of this instruction CLICK HERE



Tools Needed:

  • â…œ" Ratchet & extensions
  • 8mm, 10mm, 12mm, 14mm Sockets
  • Cutoff Wheel
  • Paint Pen
  • Hammer

Installation Notes:

    1. Read all instructions completely and carefully before you begin.
    2. Check to make sure the kit is complete and that no parts are missing. If anything is missing, please contact Trail-Gear at (559) 252-4950.
    3. Park vehicle on a clean, dry, at, level surface and block the tires so the vehicle can not roll in either direction.

2.7L Installation Instructions: (See below for 3.4L)

1. Remove the oil pan.



2. Remove dipstick bracket hardware.



3. Remove the stock dipstick.



4. Apply Ultra Grey to bottom of freeze plug.



5. Place freeze plug in stock dipstick hole.



6. Lightly tap freeze plug to secure it into place.



7. Locate the small freeze plug approximately 2" behind motor mount.



8. Using a punch, remove the freeze plug.



9. Install the new dipstick tube into the block using ultra grey at the mating surface.



10. Mark and drill a hole in the motor mount bracket to mount the dipstick tube. We drilled a 5/16" hole and used an 8mm bolt.



11. Fasten the dipstick tube to the motor mount.



12. Remove the stock strainer and install the new one.



13. Using a razor, clean the oil pan mating surface on the block.



14. Apply a bead of ultra grey to the oil pan mating surface.



15. Install the new oil pan. The strainer now sits towards the back of the truck.



16. Re-install the dust shield.



17. Install the drain plug with gasket.




3.4L Installation Instructions:



1. Remove dust shield.



2. Remove the oil pan.



3. Remove the stock strainer and replace it with the new one.



4. Using a razor, clean the oil pan mating surface on the block.



5. Mark the stock dipstick 1/8" below the full line and cut off the excess. The stock full level on the dipstick will still be used and 6 1/2 quarts of oil are used.



6. Re-install the dip stick into the block.



7. Apply a bead of ultra grey to the oil pan mating surface.



8. Install the new oil pan. The strainer now sits towards the back of the truck.



9. Re-install the dust shield. The circled bolt will need to be shortened by 3/8".



10. Install the drain plug with gasket.


Related Products

An relatable roduct