Extreme Air Intake
(Rock Ripper)
Replace your restrictive factory air filter/box with the Rock Ripper Performance Line Extreme Air Intake System.
Features:
- Engineered one piece polished stainless steel intake tubing and high performance air filter charger
- Twice the filter surface area which helps performance retention in off-road environments
- Quicker throttle response
- Twice the filtering quality
- Hose clamps and brackets all included
- Air Filter is washable and reusable
- Street & Emission Legal in all 50 US States
- Installation manual with easy bolt on steps
- Up to an extra 5 HP gain
This product should not be used in a manner that violates Federal EPA Laws.
NOTE: Any variations of parts from what is provided will void the 50-state smog certificate.
Check out LCEngineering.com for New Products, Tech Articles, Specials & Monthly Newsletters!
| Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501. |
by Trail-Gear
- 1985-1987 22RE 2.4L Pickups
- 1985-1987 22RE 2.4L 4Runners
Tools Needed:
- Ratchet and socket set
- Flathead Screwdriver
- Adjustable Wrench
- Hacksaw or Chop Saw
Installation Notes:
-
1. Read all instructions completely and carefully before you begin.
2. Check to make sure the kit is complete and that no parts are missing. If anything is missing, please contact Trail-Gear at (559) 252-4950.
3. Park vehicle on a clean, dry, at, level surface and block the tires so the vehicle can not roll in either direction.
4. Any variation from these instructions or parts will void the 50-state smog legal certification.
Installation Instructions:
1. Remove the original air duct (crossover tube) clamps and remove the air duct from the vehicle. On 1988-1995 vehicles, also remove the EGR hose from the air cleaner canister.
2. Unplug the Mass Air Sensor (MAS) electrical cord from the MAS.
3. Unbolt and remove the original air cleaner canister from the vehicle.
4. Remove the MAS from the original air cleaner canister. Mount the MAS onto the flat side of the new air cleaner canister.
5. Mount the 3/4" plastic hose fitting (or plug) into the side hole in the air cleaner.
5. Continued.
6. The portion of the wiring harness that lays on the inner fender apron below the original air cleaner canister must be rerouted rearward (out of air cleaner mounting area). Two 3/8" insulated loom clamps and sheet metal screws have been provided for this purpose.
7. Mount the air cleaner onto the inner fender apron. The front hole in the bottom of the air intake should align with the original air cleaner front hole location on the fender apron. Install 8mm bolts and nuts.
7. Continued.
8. Connect the new air duct to the throttle body hose and MAS hose. Note: If the air duct is too long, trim (with a hacksaw) the end that attaches to the MAS, not the throttle body.
8. Continued.
8. Continued.
9. Attach the new conical air cleaner to the back side of the air cleaner and tighten the clamp.
10. On 1988-1995 vehicles, attach the EGR hose to the plastic hose fitting installed in Step #5. Note: It may be necessary to purchase a new length of hose and/or fittings from a local parts store for connection between the EGR system and the Trail-Gear air cleaner on 1988-1995 vehicles.
11. Attach the MAS electrical cord to the MAS.
12. Apply the provided C.A.R.B. decal to the underside of the hood
7 Reviews Hide Reviews Show Reviews
-
very helpful with all my questions
They guided me to several upgrades that have made a tremendous and noticeable increase in power on the good ole 22re. Highly recommend the throttle body/LC header and air intake. NICE!
-
Great product and shipping was fast!
Just purchased a brand new performance air intake system. Price including shipping was cheaper and faster than Amazon. Only 3 days to Hawaii. Installed it and an instant improvement in performance and power for my 1992 Toyota 4x4. Great product and company. I will definitely be doing more business with LCE performance.
-
TG 22RE Intake system (86 4Runner)
Nice quality intake system. Chrome intake tubing, silicone hose to air flow meter, T-bone clamps, heavy duty air cleaner bracket & air cleaner. I had to cut 2" off the intake side of the tubing & 1" off the afm tube side. But all together, fits & looks nice. Sounds mean!
-
neat
looks cool, sounds cool, performs cool
-
Great place to shop
Nice intake very helpfully people an lc performance. When u call u get to talk to a real person not a machine!
-
intake kit / bearing sets
excellent customer service!
-
rock ripper air intake
Looks like a great product. Didn't come with any instructions though.
