Weber 38 Carb & Intake Performance Package - 22R
Includes: Weber 38 Carb, Intake Manifold and Chrome Air Cleaner w/K&N Filter
**CURRENTLY OUT OF STOCK - ETA is 5 weeks as of 03/05/2017**
One of the best ways to get some extra performance out of your little Toyota 22R is to upgrade the carburetor and intake manifold. It is always important to match your upgrades to each other to make sure everything works well together, so with this kit LC Engineering has done all the homework to make sure that you get the perfect combination of parts to maximize your performance.
This Carb & Intake Performance Package contains a Weber 38 carburetor kit, with a Chrome 11" x 2" K&N air filter and a single plane intake manifold.
Recommendations from LC Engineering:
upgrade kit is recommended for vehicles looking to achieve more than
130 Horsepower, some other recommended upgrades are: Performance
Camshaft, High Flow LCE Headers, Upgraded Ignition and Over-sized
Single Plane Downdraft Intake Manifold
With a large open plenum and runners, this manifold will outflow your stocker and supply your performance engine with enough airflow to make the most horsepower possible. The single plane design of this manifold provides excellent mid range to upper RPM power without sacrificing low-end torque. This manifold is equipped with a Weber carburetor flange so you can bolt your performance carburetor on the manifold without having to use any adapters. This manifold has all the same vacuum and sensor ports as your stock manifold so you don't have to worry about adapting different fittings together to get all your vacuum lines and temp sensors hooked back up!
Weber 38 Carburetor Kit
Unleash the sheer power of your performance vehicle with the Weber 38 Carburetor. Manufactured to deliver maximum speed and horsepower, the Weber 38 is a two-barrel synchronous electric choke carburetor. Due to its impressive performance output, this carburetor is used and trusted by countless racers that require top performance from their 4 cylinder engine.
K&N Chrome Air Cleaner w/K&N Air Filter
K&N's custom air cleaner assemblies are designed with the racer in mind. They incorporate good looks as well as the superior air flow that you expect from K&N. These custom air cleaner assemblies are designed for use with any engine that uses a round element air cleaner housing. They incorporate our famous K&N Air Filters and provide more air flow than other assemblies of this type. Each complete assembly comes with base, element and top plate.
Optional Parts Info
The manifold in this kit is designed to use a rubber style thermostat gasket (supplied with manifold). There are a few other upgrades available for this manifold so take a minute to browse through the parts below to see if you will need any of them for your application. If you have any questions please contact one of our sales reps to help you determine what parts you may or may not need.
Requires 2.5 - 3 lbs of fuel pressure, see regulator kit part# 1035056
Factory fuel line from mechanical pump is roughly 1/16" smaller than WeberRegulator/Carb fuel line. Slight pressure is all that is needed to fit the smaller line.
Part #1032021Intake Manifold Gasket
Part #1032091Teflon Intake Manifold Gasket
Part #1032086Thermostat Housing Adapter
Part #10320038 Bolt Water Plate(Under Manifold)
Part #1016015 Pro Water Block Off Kit
Part #1032050 Intake Manifold Plug Kit
Part #1016038 EGR Block Plate Kit
Part #1035048 Intake Manifold Stud Kit
Part #1033023 Weber Spiral Spacer
Warning: Single plane manifold uses an 8 bolt water plate(under manifold)
Warning: Single manifolds require an 81-83 style thermostat housing
Contact our Tech Support Line for further information at 928-855-6341.
Check out www.LCEngineering.comfor New Products, Tech Articles,Specials & Monthly Newsletters!
Note: Images are for illustration purposes only. Images MAY NOT represent the product listed. Please contact Customer Service with any questions or concerns: 928-505-2501.