Home > ELECTRICAL & IGNITION > Ignition & Distributors > Spark Plug Wires & Plugs >

NGK 7mm Spark Plug Wire Set 20R/22R/RE/RET 1978-1992
NGK Spark Plug Wire Set 20R/22R/RE/RET 1978-1992

Alternate Views:

Our Price: $31.42

Part Number: 1083032

NGK Spark Plug Wire Set 7mm 20R/22R/RE/RET 1978-1992

We realize not every engine is a race engine. Don't over spend on features that you can't use. The NGK spark plug wires are perfect for the street were high RPM's are not sustained and upgraded ignition are not used.

NGK Resistor Spark Plug Wire Sets utilize a construction method known as "variable pitch" wire winding to create resistance to radio frequency interference. The variable pitch winding (loose/tight/loose) provides suppression throughout a very wide range by "scrambling" and breaking up the electrical waves radiated by the firing of the spark plugs.


A ferrite magnetic layer consisting of a mixture of rubber, plastic and powdered ferrite magnetic materials, offers uniform resistance and unsurpassed conductivity. NGK wires have a lower resistance than conventional carbon core wires (8k ohm/meter vs. 16k ohm/meter). This comparison is important to remember when you consider that many manufacturers recommend wires be replaced when the resistance exceeds 20k ohm/meter. This does not leave much margin for wear when the wire may only meet original standards at the very early stages of its life.At the center of NGK Resistor Spark Plug Wire Sets is a fiberglass stranded core, made from the same family of materials used in bullet proof vests. This core greatly enhances the overall strength of the wire, providing a super strength backbone on which the various layers of the wire assembly are formed. The core gives protection from damage caused by the pulling strains that wires are often subjected to and that can destroy their performance.

High quality EPDM and Silicone coverings are used to resist high heat, oil and chemical damage for increased durability.

Custom designed terminal boots are always used to provide exact fit (not universal fit like other major wire manufacturers). Each NGK ignition wire is fitted with a positive locking, corrosion resistant Stainless Steel terminal end for tight fit and maximum resistance to vibration and separation.

NGK Wire Sets are numbered for easy cylinder identification and coil wires are color coded for correct and easy installation

  • Superior Firing and Fuel Savings
  • Outstanding Durability
  • Consistent Performance
  • Excellent Noise Suppression
  • 7mm Wire
  • Uses The Stock Plug Wire Hold Downs
We always recommend use of our Race Wires for any highly modified late model engine that is electronically managed, Race or street engines can also use our Pro Wires to improve ignition performance. See part number 1083009

Contact our Tech Support Line for further information at 928-855-6341.

Check out www.LCEngineering.com for New Products, Tech Articles,
Specials & Monthly Newsletters!
Note: Images are for illustration purposes only. Images MAY NOT represent the product listed. Please contact Customer Service with any questions or concerns: 928-505-2501.

Average Customer Review: 4.5 of 5 Total Reviews: 3 Write a review.

  0 of 0 people found the following review helpful:
. July 3, 2018
Reviewer: David Cerce from Leicester, NC United States  

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Good fit May 1, 2017
Reviewer: John Swyers from Tulsa, OK United States  
The wires were an exact fit. The boots are easy to install or remove and the color matched my new vacuum lines!  I got them in 2 or 3 days

Was this review helpful to you?

  0 of 0 people found the following review helpful:
Sweet staff June 2, 2014
Reviewer: Gaston Perez from Yakima, WA United States  
Great product!!!

Was this review helpful to you?

Browse for more products in the same category as this item:

ELECTRICAL & IGNITION > Ignition & Distributors > Spark Plug Wires & Plugs