Fuel Pressure Gauge Kit
(Low Pressure Only/Dry Gauge)
If you are running a Weber carburetor on your Toyota truck, this kit is a must-have and a great way to keep your fuel system running right. Weber carbs work best in the 2.5-3psi range. This kit provides you everything you need to dial in the fuel pressure accurately to help your carburetor perform at its peak.
This kit includes a genuine Weber regulator, custom made in the USA fuel line "T" fitting and a quality low-pressure gauge so you will know exactly how much pressure your fuel system is delivering to your carb, and this is very important when you are trying to correctly tune your carb to achieve peak performance.
NOTE: The factory fuel line from the mechanical pump is roughly 1/16" smaller than Weber Regulator/Carb fuel line. Slight pressure is all that is needed to fit the smaller line. This gauge is intended to be used as a tool if you're interested in a more permanent gauge see Part #1035055. Premature failure may result from leaving the gauge installed underhood. Not for use in the cabin of the vehicle.
| Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501. |
- 1975-1980 20R 2.2L Engines
- 1981-1995 22R 2.4L Engines
Fuel Regulator
To open a printable PDF version of this instruction CLICK HERE
Specification Notes:
- This high quality adjustable fuel pressure regulator is adjustable from 1.5 - 20 psi.
- This regulator should be mounted on the firewall or the inner fender.
- Fuel hose size is 8mm or 5/16".
- In and out are marked on the housing.
- If you are using a liquid-filled gauge, gauge reading must be done when cold.
Installation:
1. Remove cap using a 12mm wrench
2. Loosen the locking nut at the bottom of the adjuster screw.
3. Using a flat screwdriver and a fuel pressure gauge, adjust the fuel pressure to the desire pressure. Turning screw clockwise will increase pressure, counter clockwise will decrease pressure. Adjust in half turn increments. Weber Carburetor recommended fuel pressure is between 2.5 psi. and 3 psi.
4. Lightly tighten the locking nut making sure the adjustment screw does not move.
5. Tighten the cap while holding the locking nut (the one on the bottom) with another 12mm wrench, so adjustment screw won't move.
Fuel Gauge Kit
To open a printable PDF version of this instruction CLICK HERE
Kit Contents:
- (1) - LC Low Pressure Fuel Gauge
- (1) - Fuel Pressure Gauge "T" Fitting
- (1) - Hex Socket Pipe Plug
To install, simply cut fuel delivery hose and place in-line. If you're installing a regulator, you'll want to install a "T" Fitting after regulator. You may have to "walk-it" onto each end of the fitting as it'll be very tight. Once "T" fitting is in place, thread gauge in.
NOTE: Do not use hand to tighten gauge. Failure to do so could result in damage to gauge. Please use wrench on backside of gauge to tighten.
After fuel pressure is set, remove gauge and plug w/ provided pipe plug. Leaving the gauge installed will result in gauge failure.
62 Reviews Hide Reviews Show Reviews
-
Press reg
Works as designed Nice piece, a little expensive
-
Anonymous give 5 stars
-
Grunt
Got it quick, put it on in a snap, didn't even have to fine tune it. It was adjusted perfectly. Took the gauge off and thru it in the glove box put the plug in and drive off.
-
Fuel pressure regulator
Easy installation and adjusting. The included gauge made it simple to adjust to the 2.5-3 psi required for the Weber 32/36
-
.
.
-
.
Have not installed yet but delivery was on time and tech support when ordering was great. Looking forward to more power for the Toy.
-
.
.
-
.
Fast shipping Good quality
-
.
.