LCE Kit

LCE Street Header Kit 3RZ Tacoma 1995-2004 Single Cat. ONLY (50 State Legal up to 1999)

SKU: 1041054
0
(83 reviews) Write a Review
$584.29
Adding to cart… The item has been added

Tacoma Street Header Kit

(50 State Legal 1995 - 1999)

This high-quality header is a long tube design to get the most horsepower for your Tacoma. There are other headers on the market but none will come close to the LC Engineering long tube in terms of horsepower and torque gains. This header kit will come with new OE the gaskets needed for install.

All the same quality components used in our 22R line are now available for your 2RZ or 3RZ engine. Our header kits for the 3RZ are made from 1-5/8" 304 stainless steel tubing, 16 gauge .065 wall, and feature 1/2" thick flanges at the head and 3/8" thick flanges at the collector. 3RZ header has a 2 1/2" collector to bolt to the factory catalytic converter. For the best performance, our headers are ceramic coated for long-lasting great looks and lower underhood temps. Kits include all gaskets needed for proper installation. LC Engineering 2RZ/3RZ header kits are a direct fit on single catalytic trucks only. Trucks with dual catalytic converter applications will require modification to use LC Engineering's header kit.

NOTE: Not a direct fit for vehicles with dual catalytic converters. 2RZ and 3RZ header kits are 49-state legal for all years, but CARB legal in California only for 1995-1999 Single Catalytic Converter trucks. LC Engineering does NOT recommend wrapping our headers with any sort of exhaust wrap. Doing so will increase the likelihood of a premature failure of the header, as it holds contaminants to the exhaust tubing and increases the chances of corrosion. Exhaust wraps will void any and all warranty claims.



Note: Images are for illustration purposes only. Images may not represent the product listed. Please contact customer service with any questions or concerns: 1-928-505-2501.

  • 1995.5-2004 3RZ 2.7L Tacoma Engines

To open a printable PDF version of this instruction CLICK HERE


Your LC Engineering Street Performer Header Kit is supplied with the necessary gaskets and hardware for installation. This header kit replaces the stock exhaust manifold and connector tube. It is designed to bolt directly to your factory catalytic converter. This Header Kit utilizes all factory emission and oxygen sensor equipment in stock locations and performs to OEM requirements. Follow all factory service manual recommendations for removal of stock exhaust manifold. Reverse instructions for installation of LC Header Kit.


Exhaust Studs:
Torque exhaust studs to 33ft-lbs. We also offer new header mounting studs if needed (part #1045030).


NOTE:
LC Engineering does not recommend the use of header wraps.


83 Reviews Hide Reviews Show Reviews

  • 0
    5
    2.7l Toyota header

    Posted by Nicolas Williams on Oct 6th 2020

    Header bolted up and fit perfectly to the cat and the egr system. Couldn’t have asked for a better product. Thanks LCE!

  • 0
    4
    LCE Headers for 1998 4cyl tacoma

    Posted by Matt Austin on Jul 30th 2020

    Great Headers, easy installation. I have an auto (sadly) the tranny fluid dipstick was kind of a pain but I ended up just zip tying it since I couldn't bolt it back into place. I'm sure it could be done but I was tired and lazy. Definitely recommend buying the extra set of head bolts and doing that while you're in there. Not sure how much horsepower gained since I didn't dyno it but it sounds and feels better. Overall LCE is a good company, they delivered and I wouldn't go with anyone else.

  • 0
    4
    EGR DELETE

    Posted by Daniel Muzzone on Jul 29th 2020

    Excellent quality hands down.. just like always. Just one thing I'd have added to kits if up to me.. supply more detailed instructions for egr delete kit. While it's obvious once I've found an outside write up, I wasn't confident about where to snip and solder the resistors. I snipped the wires as close to temp sensor as possible leaving the two wire tails plugged in. Soldered both resistors together, and the remainder resistor tails are soldered to the temp sensor wire tails. Tape up and done Easy peasy, the most challenging aspect was just searching for the procedure on the web. After the wiring, just use the original coolant hose (the longer of the two thats attached to egr) to close the coolant loop. No check lights. Remember to always detach negative battery terminal before any wire work. Will order lots more from LCE in the future.

  • 0
    5
    .

    Posted by Robert Le on Jul 26th 2020

    .

  • 0
    5
    3RZ Header

    Posted by Jason on Apr 3rd 2020

    .

  • 0
    5
    Header 2.7 toyota

    Posted by East Maui on Apr 3rd 2020

    Quality product, fast shipping , easy install ,

  • 0
    5
    Not obnoxious

    Posted by K G on Feb 7th 2020

    Looks awesome under the hood and through the wheel well.

  • 0
    5
    Better performance than I expected

    Posted by JP on Dec 24th 2019

    I had some troubles with my aftermarket factory style manifold leaking, decided to upgrade to a LCE CARB legal header. Glad I did. No flange to leak and the performance was better than I expected. It runs smoother and has better usable power. I’ve had a few 1st gen Tacoma’s and should have installed this header on all of them.

  • 0
    5
    3rz header

    Posted by Junior on Nov 19th 2019

    So easy to install! No unforeseen modifications to get this header to fit. Dropped right in. Hardware and gaskets included. Such a dramatic increase in performance!

Videos Hide Videos Show Videos

Related Products

An relatable roduct