LCE Street Header Kit 4wd Direct-Fit 22R/RE 1985-1995

Street Header Kit for 1985-1995 22R/RE Toyota Engines (4WD)

(50 State Legal C.A.R.B. EO: D-462-1)

Whether your 1985-1995 Toyota truck is bone stock or built for extra performance, the LC Engineering Street Header for 22R/RE engines is the "best bang for your buck" bolt-on part you can buy. You should expect to see a 10-15% power increase with a good boost to the top end of the powerband where these trucks struggle. With so many choices for a header on the market, some certainly being cheaper, we can understand if you are struggling with the decision of which one to buy. We can tell you there is a good reason why our header is still #1 on the market and worth the extra cost.

Our most popular product is the street header kit. LC Engineering uses all 304 1 1/2" Stainless steel tubing, a huge 1/2" thick steel header to the head flange, and a 3/8" thick steel 2-1/4" flange at the collector that accepts the stock Toyota round exhaust gasket. So it's an OE fit. As if that were not enough, the whole package is coated in a high-temperature ceramic coating. To make the installation easy on you LC Engineering supplies you with all the gaskets needed to bolt your header on your vehicle. Our header flanges are cut to allow the use of OEM exhaust manifold gaskets. These gaskets feature a metal crush fire ring and a heat deflector for the plug wires. No cheap paper gaskets to blow out with an LC Engineering Header.

Here are a few reasons why:

• Made with high-quality materials.
• Coated in a high-temperature ceramic coating.
• Gaskets Included
• LC Engineering has been designing, testing, producing, and installing 22R/RE street headers for more than 20 years.
• Since we focus on Toyota performance parts we spend the extra time to make these headers the best they can be.
• Our head side flange is designed to retain the use of the OEM exhaust manifold gasket, the gasket features a metal crush fire ring and a heat deflector for the spark plug wires.

Kit Includes:

• 4WD (82-95) Street Header
• 4WD Connector Pipe
• Street Header Gasket Set (85-95 Specific)

All Toyota Pickups and 4Runners manufactured before 1988 have a factory non-heated single-wire oxygen sensor. When installing our Street Header Kit you will notice that the oxygen sensor provision has been moved downstream from its factory location. We recommend that anyone with a pre-1988 application utilize our universal 4-wire heated O2 sensor in replace of their factory single wire. This will not only improve the signal but the gas mileage as well as the performance of the vehicle. Vehicles made from 1988-1995 should have a factory-heated O2 sensor and should not need to change it unless their factory one is damaged.

NOTE: If your O2 sensor is located in the exhaust manifold then you need to check the box for O2 Relocation Kit. If by any chance you did not select it with your kit and you need it, don't worry all you need is 18 gauge wire and 2 small crimp connectors from your local auto part store. LC Engineering does NOT recommend wrapping our headers with any sort of exhaust wrap. Doing so will increase the likelihood of a premature failure of the header, as it holds contaminants to the exhaust tubing and increases the chances of corrosion. Exhaust wraps will void any warranty claims.

Installation Note:

Over 20+ years of producing these headers LC Engineering has made all attempts to make these header kits fit as best as possible. Unfortunately, there is a very small amount of applications that may require more extensive modification or even fabrication to make the connector pipe fit correctly. This is mostly contributed to numerous changes in Toyota's production along with aftermarket modifications. LC Engineering offers full technical support to make your fitment as easy as possible but they will not be responsible for any "custom" connector pipes.

NOTE: Due to many fitment differences, we cannot quote fitment to any RV. These were a custom vehicle and not a standard dealership vehicle. We do have a Test Fit Header that we can ship to you with a return label for $75. This will be the only way to confirm fitment to anything considered an RV.