Trail-Gear

Transfer Case Shift Base If you are going for the multiple transfer cases setup, you will need shifters too! Great replacement for your old or broken Toyota stock shifter. NOTE: Does not...

Transfer Case Shifter Kit Stock replacement shifter handle and base. Bolts in using stock bolts. This product should not be used in a manner that violates Federal EPA Laws. Contact our Tech...

Trunnion Bearing Eliminator Kit Anyone who wheels hard, rock crawls, or rock races has experienced blown up trunnion bearings, no matter what size bearings they are using, the bearing is always the...

Tube Bumper | Options Available Defend your classic rig on the toughest trails with the All-Pro Series Front Tube Bumper. Engineered to meet the extreme demands of rock crawling and hardcore trail...

All-Pro Off-Road Front Tube Bumper Defend your classic rig on the toughest trails with the All-Pro Series Front Tube Bumper. Engineered to meet the extreme demands of rock crawling and hardcore trail...

Tube Bumper | Options Available Defend your classic rig on the toughest trails with the All-Pro Series Front Bumper. Engineered to meet the extreme demands of rock crawling and hardcore trail riding,...

Creepy Twin T-Case Shifter (Forward Shift) Twin stick shifters allow independent control of the high/low and 2wd/4wd sections of your Toyota gear driven transfer case. This allows access to low...

Creepy Twin T-Case Shifter (Top Shift) Twin stick shifters allow independent control of the high/low and 2wd/4wd sections of your Toyota gear driven transfer case. This allows access to low range...

Stick Shift Boot (Twin T-case) This boot is designed to work with our Creepy Twin T-Case shifter (above). It features a flexible rubber shell with a steel bottom plate for mounting to your floor...

Ultimate Chevy 63" Spring Swap Kit Upgrade your Toyota Hilux, 4Runner, or Tacoma with the legendary Ultimate Chevy 63Spring Swap Kit from Low Range Off-Road. Renowed in the off-road community for...

Trail-Gear Front 3-Link High-Steer Suspension System Engineered in response to driver demand, the Trail-Link Three High-Steer Kit is the industry’s only all-inclusive 3-link front suspension...

Unit Hub (Dana 60 / 9" Housing) These unit hubs are not just another aftermarket 1-ton unit hub that has been machined down and modified from an 8 lug to a 6 lug application. This hub has been...

Universal Steel Tube Clamp: Multiple Size Options Available The Trail-Gear Steel Tube Clamp (1.00" OD) is a high-performance solution for off-road fabrication, offering a secure way to mount brackets...

Upper Link Mount (OEM / Rock Assault) Trail-Gear customers tend to drive where the majority would never ventureâ€"climbing over rocks, hills, and rugged off-road terrain. Hobbies like that...

Upper Gusset (Solid Front Axle) This gusset welds on top of your Toyota front solid axle and helps prevent bending of the axle housing. This product should not be used in a manner that violates...

Vented Non-Cross Drilled Rotor Toyota Pick-Ups and 4Runners (86+) feature larger vented rotors from the factory. Earlier (79-85) trucks used solid, non-vented rotors up front along with smaller...

Steering Rod Bungs (Weld In) Finally a weld in bung with the thread pitch of an FJ80 Tie Rod Ends, which is the most commonly used Tie Rod Ends in Toyota hi-steer kits. Once welded into your tie...

Weld On Flat Tab Standard (You Choose Size) TG Weld On Coped Tabs are made from steel, 3/16" thick with a 1/2" diameter hole, and are available in standard or offset. Tabs are coped for either 1...

Weld On Flat Tab (3" Cope) Our 3" coped weld on flat tab is made from 1020 hot rolled steel, 1/4" thick, and is designed for a 9/16" bolt. The width is 2" and the overall height is 2-15/16". The...

Weld On Flat Tab (9/16" Hole) Our weld on flat tabs are made from 1020 hot rolled steel, are 1/4" thick and are designed for a 9/16" bolt, they are 2" wide and 2 5/8" tall. The center of the hole...