LCE Kit

Holley 350/500 Carb to Weber Manifold Adapter Kit We manufacture these billet aluminum carb adapters in house, to our specs. We use only the finest materials in our spacers to assure the quality...

Air Injection Adapter Kit This adapter kit is needed to retain air injection when using one of our headers on your early 22R. For customers who need to pass emissions tests, especially in...

Air Injection Gasket The air injection gasket goes between the header flange and the air injection tubes. This gasket is also used with our air injection block plate, see Part #: 1045000. NOTE:...

Air Injection Gasket LC Engineering only uses factory Toyota exhaust gaskets on the 2TR Exhaust or our Street Header. This ensures that you get the best seal on your exhaust with no chance of...

Adapter Kit (Stock Aisin 22R Carb to 20R Manifold) LC Engineering Manufactures a billet adapter to mount a stock 22R Aisin carburetor to a stock 20R intake manifold. It comes with necessary...

Adapter Kit (Aisin 22R Carb to K&N Filter) LC Engineering manufactures custom adapters to match your Aisin 22R carburetor to a K&N or similar flanged air filter. NOTE: Fits any filter...

Balance Shaft Removal Kit   This kit is designed to eliminate the balance shafts in a 3RZ or 2TR engine. Kit includes new bearings, replacement inserts, billet aluminum install driver, oil...

Billet Valve Cover Hardware Kit 22R/RE (Includes Billet Valve Cover Seals, Studs & Acorn Nut) Looking to turn heads at your next show? Then look no further than our new hand polished fasteners that...

Billet Wire Loom (LC 8.5mm Pro Wire Separators) Not only does this setup look great, but the LC Engineering billet plug wire loom allows you to route your wires away from exhaust heat without...

Billet Wire Loom (11mm Livewire Separators) Not only does this setup look great, but the LC Engineering billet plug wire loom allows you to route your wires away from exhaust heat without worrying...

Brake Hard Line Kit (Left & Right) This caliper hard line kit is for straight axle Trucks and 4Runners only. This kit includes the caliper brake lines for both the right and left sides. NOTE:...

Solid Axle Vented Rotor Upgrade (Front) This kit is designed to change the solid stock rotors that are found on the front straight axle 1980 to 1985 trucks or SAS using the stock Toyota front axle...

Brass Freeze Plug At the beginning of any complete engine build-up, the block needs to be cleaned. To do that, all of the block's plugs must be removed (even with a new engine) to allow cleaning...

Builder Series (Pro Engine Kit) Toyota engines are known for their longevity. So it is no surprise to see some of these with 200,000 plus miles on them. Unfortunately, they will need some attention...

Builder Series (Street Engine Kit) Toyota engines are known for their longevity. So it is no surprise to see some of these with 200,000 plus miles on them. Unfortunately, they will need some...

Cam Degree Kit Cam degreeing can be a scary procedure if you are not prepared for it. LC Engineering has just made it a lot easier by creating a kit that is designed to work on your 20R, 22R/RE/RET...

Cam Follower Kit (Shim Under Bucket) Cam Followers (or Bucket Lifters) and Lash Caps are designed using the latest CATIA CAD software and Finite Element Analysis (FEA) for the high demanding...

Cam Follower Kit (Shim Under Bucket) These 34mm cam buckets are designed for use with larger cam profiles in your 2RZ or 3RZ engine. The larger outside diameter allows the cam profile to be much...

Manifold Install Kit (9 Bolt / 20R) One of the most important keys to building a performance engine is to have components that all match up and are designed to work together well. You can put the...

20R Intake Manifold Plug Kit This plug kit comes with all the necessary plugs for a Cannon Intake Manifold. There are two holes that need this shouldered plug to seal. If you look at the picture...